![rs-ba1 volume control rs-ba1 volume control](https://i.ytimg.com/vi/G4e3kzB9qaE/maxresdefault.jpg)
#Rs ba1 volume control software
This software is designed to operate with Windows® 7, Windows® 8.1 and Windows® 10 on a PC with 1.8 GHz processor or better, 150 Mb HD, 1024x768 resolution. The RS-BA1 provides highly qualified audio communication between your PC and an Icom amateur radio. With the RS-BA1, you can configure a remote control system through the Internet, or a LAN. The IC-7300 can be connected to a PC via a USB cable and the input/output audio signal and CI-V command is sent through the USB cable. iii Overview of the RS-BA1 The RS-BA1 consists of the Remote Utility, used to configure a remote control system, and the Remote Control- ler, used to send CI-V commands to a radio to remotely operate it. Remote control software provides a user interface, similar to the radio's front panel, and allows you to control the radio from a remote location. System configuration software sets up IP address, audio sampling rate and other settings.Ģ.
![rs-ba1 volume control rs-ba1 volume control](https://i.ytimg.com/vi/crYCBeu1yR4/maxresdefault.jpg)
The RS-BA1 Windows® CD consists of two component software applications:ġ. Shown above in use with a dual-receive transceiver. ICOM Might want to add a feature to RSBA1 to show the setting of each object/control that is shown in the simulated radio display.This is what a Tool Tip pro. The RS-BA1 Version 2 can also still be used with single-receiver transceivers. The RS-BA1 Version 2 can also enlarge the panel size (normal or large is selectable), buttons added, clickable indicators to change settings, SUB dial added and RIT tuning knob & TX functions added. With the RS-BA1 Version 2, you can use the dual watch operation and spectrum scopes with waterfall function as well as observe the MAIN and SUB spectrum scopes. The S-Meter and SWR can even be observed.
![rs-ba1 volume control rs-ba1 volume control](https://i.ytimg.com/vi/FIOUdFx6r0g/maxresdefault.jpg)
Low voice latency (caused by the RS-BA1) provides the same operational experience as using an actual radio. Most functions and modes of your Icom compatible transceiver can be controlled, including interference rejection functions and IF filter settings. I may revisit this review once I have time to use it more.The Icom RS-BA1 v2 IP Remote Control Software allows you to use an Icom compatible radio installed in another room using your home network or even from a remote location over the Internet. Also could not import from Excel my memory setup. It cannot seem to read what I had programmed into the radio with RT Systems software. So I'm still trying to sort that out.Īnother issue is the memory functions. The button to key the mic works, but you can talk all day long and it won't send. One item I don't like is EVERY time I connect the radio, the software shuts the mic input off. Running the program is not super difficult, but not everything is intuitive. Once that was set, it connects every time now. The initial setup in Win10 was easy to install, but connecting to the radio took some work and required getting into the Device Manager console to set the COM port.
![rs-ba1 volume control rs-ba1 volume control](https://s1.manualzz.com/store/data/014390704_1-1440d8d441487b476f6eea9e98a3f6b9-360x466.png)
A Spectrum Scope function has been added.(only for the IC-7850/IC-7851s with firmware version 1.10 or later) The Remote Control main screen's design has been changed. It has not been the easiest computer controller software to use, but not the hardest either. Control software: Model name: RS-BA1: Version: Version 1.80: Update: 7: Major changes: Improvements. I bought this software when I bought my Icom IC-7100. (For a single band on only the IC-7851, 78) Rx Voice recording function. The spectrum scope with the waterfall function can be observed on the RS-BA1. Slider control or tuning knob control screens are selectable for RF power, CW pitch, RF gain, and SQL and AF level. I only have a little experience with computer control of the radio. Advanced Remote Control Interface Tailored to Icom Transceivers. Mainly using this on 6 and 10 meter right now.ī. I'm new to HF radio's as I am still a Tech class operator.